PLA
Showing 17–24 of 24 results
-
DetailsFilaticum Wood
13 490 Ft – 44 890 Ft 10 622 Ft + VAT Add to cartFilaticum Wood filament is designed to create objects resembling real wood in texture and color. Printing settings are the same as those for standard PLA, and you should pay attention to the same things. The nozzle clogging is not an issue with Filaticum Wood, as it I usually a case with wood filaments.
At the same time, the adhesion is excellent, shrinkage is minimal.
The wood effect is also enhanced by the fact that the printed object has a unique touch that is rougher and more natural than PLA. In addition, it is relatively easy to sand and simple to paint.
-
DetailsFilaticum Fuzzy
9 990 Ft 7 866 Ft + VAT Add to cartFilaticum Fuzzy filament was developed to create unique objects with a special surface. The layers typical for FDM 3D printing are blurred, almost disappeared, as a fluffy, fuzzy surface is formed over them. This is combined with a matt effect.
Filaticum Fuzzy is PLA-based filament, therefore PLA printing settings can be used as a baseline, and then, the surface texture of the printed object can be modified by varying the printing temperature. Recommended bed temperature: 60 °C.
For an even more special look, with a lower flow a surface with “craters” can be achieved.
In addition to the unique surface, the impact resistance of the material is also very good, it is easy to sand, post-process and glue also. The Z-axis adhesion of the print is also better compared to standard PLA filament.
To achieve the characteristic surface, in addition to PLA this filament contains additives, making it somewhat stiffer than usual. Due to the nature of the filament, it is prone to stringing, but this can be easily removed after printing without traces.
The spools weigh 750 grams, but they contain the same amount of filament length as standard 1 kg PLA filaments, so the material requirement should be calculated accordingly.
-
DetailsFilaticum Antiviral
29 990 Ft – 99 890 Ft 23 614 Ft + VAT Add to cartFilaticum Antiviral provides antimicrobial protection for the entire lifetime of 3D printed products. The active substance, built in to the PLA matrix, has been shown to deactivate many kinds of viruses and has been tested to be effective against Feline Coronavirus, H1N1 and Norovirus viruses, among others. The latest tests (according to ISO 21702) by the producer of the active substance confirmed, that the reduction of Covid-19 (SARS-CoV-2) germs is much faster than in the control samples without active substance. Thus, the active substance can be used effectively in the protection against Covid-19, however, the antiviral activity of the 3D printed product has to be tested by the manufacturer of the final product in a specialized laboratory.
-
DetailsFilaticum Antibacterial
27 490 Ft – 91 490 Ft 21 646 Ft + VAT Add to cartFilaticum Antibacterial is a special filament which provides antimicrobial protection against a wide variety of microorganisms. Its antibacterial and fungicide properties are based on metal ions. In objects printed with Filaticum Antibacterial filament, the built-in metal ion complexes block the metabolic processes of bacteria and fungi by an enzymatic reaction, thus preventing their growth. A similar mechanism is present at disinfectants, various preservatives, wash-off and leave-on products.
Filaticum Antibacterial provides lifelong lasting antimicrobial protection against Gram positive (e.g. Enterococcus, Bacillus etc.) and Gram-negative (e.g. Salmonella, Legionella etc.) bacteria, and different fungi, yeasts and algae fungus. Its use is advantageous where the presence of these microorganisms is harmful, e.g. in hospitals, shops, households, beauty salons. With Filaticum Antibacterial, objects exposed to microbial infection can be 3D printed.
The active metal ion substance is incorporated in the PLA polymer matrix, and it does not have any negative impact on PLA’s favorable mechanical and printing properties. Filaticum Antibacterial can be printed in wide range temperature: 195-215 0C, without changing antibacterial properties. Solubility of the active metal ions and their migration to the surface is very low, so the dissolution from 3D printed objects is minimal, providing long-lasting protection for the object.
The active antimicrobial substance has been extensively tested using internationally accepted methods: ISO 22196, ASTM E2180 and JIS standards.
-
DetailsFilaticum Cleaning
1 890 Ft 157 Ft + VAT Add to cartFilaticum Cleaning was designed for cleaning the extruder and the nozzle. This special filament incorporates short glass fibers thus removes staining and polishes the inner surface. Recommendation of use: print about 20 cm filament which cleans the extruder. If the outflow material clean, it means that the extruder is also clean. In some cases a little bit more material is needed. The efficiency of the cleaning process could increase, if you stop the printing for a while and then continue it. Regular use of Filaticum Cleaning reduces the plugging, increase the shelf life of the extruder. It is also strongly recommended if you changes often the different colored filaments or swap different raw materials.
-
Details
Filaticum Support
11 690 Ft – 38 890 Ft 8 661 Ft + VAT Add to cartFilaticum Support is a PLA-based filament, developed for 3D printings which need support.
As opposed to the soluble support materials Filaticum Support is an easy to break-away filament, so the vast majority of the support material can be removed quickly. Any remaining support on the surface can be completely removed by sanding. The result is a clean printing surface, there is no or minimal need for post-processing.
Also suitable for printing the complexly structured supports. It is compatible with FDM filaments and works well with them.
Printing with Filaticum Support is simple, settings are similar to PLA’s: printing temperature 190-215 0C, bed temperature 60 0C.
-
DetailsFilaticum Glass Reinforced
18 990 Ft – 63 290 Ft 14 953 Ft + VAT Add to cartThe strength, hardness, and heat resistance of filament reinforced with glass fiber go far beyond the characteristics of the standard PLA. It can withstand heat of up to 100 0C. The biopolymer-based filament is also suitable for printing lightweight parts, even applicable for replacing metal parts. The printed surface is unique, glassy, so it is also a perfect choice for designers. The warping of objects printed with Filaticum Glass Reinforced is very low. Recommended printing parameters: 215 0C nozzle, 60 0C bed. If you are printing continuously in bigger quantities (above 1-2 kg), hard nozzles are recommended, in this case the printing parameters should be adjusted accordingly. Direct drive is recommended.
-
DetailsFilaticum High Transparent
14 990 Ft – 49 890 Ft 11 803 Ft + VAT Add to cartTransparent PLA filaments have a slight yellowish color, in addition, if you print thicker objects, the transparency disappears. With Filaticum High Transparent you can get an almost water-clear finish. It is an easy-to-print filament, in a wide range of printing temperature. The transparency of the printed object can be improved by changing the printing parameters: a nozzle with larger diameter, and the lowest possible layer height. It’s important to know that the texture of the print can also affect the transparency, and the best results can be obtained by printing single-layer walls.