1,75 mm
Showing 17–30 of 30 results
-
DetailsFilaticum Electrical: Conductive
36 990 Ft – 123 290 Ft 29 126 Ft + VAT Add to cartFilaticum Electrical products are used mainly in the electronics and automotive industry where electrostatic charging of the printed object can damage the product. Objects printed with Filaticum CONDUCTIVE, ESD or ANTISTATIC do not charge electrostatically due to the special carbon and chemical additives. Additionally, the dust and fine powder does not stick on the surface.
To decide for which application which filament suits the best, can be determined mainly experimentally. It depends on the electrical and mechanical requirements of the objects, and the 3D printing parameters. Filaticum Antistatic has the best mechanical properties, similar to standard PLA. Filaticum Conductive is the most rigid in this line, because of the used carbon powder and fiber, required for conductivity. Filaticum ESD is somewhere in the middle range.
Filaticum Conductive provides surface resistance at megaohm order of magnitude, but this highly depends on the size and shape of the printed object. As a rule of thumb, if the printing temperature is higher, the surface resistivity is lower.
Usually, any type of bed surface can be used, direct drive is recommended.
-
DetailsFilaticum PA Carbon
29 990 Ft 23 614 Ft + VAT Add to cartStrong, rigid and heat resistant (up to 180°C) composite. Polyamide 6 stands as one of the toughest materials utilized in FFF 3D printing. Its exceptional mechanical strength, stiffness, vibration damping capabilities, and wear resistance surpass those of other filament types. In addition, it offers excellent chemical resistance also.
The carbon fiber content diminishes shrinkage, which is common in most high-temp materials, so that it simplifies the printing process also. The carbon fiber enhances more the stiffness and tensile strength (up to 120 MPa) of filament.
-
DetailsFilaticum Essence
9 990 Ft – 33 290 Ft 7 866 Ft + VAT Add to cartFilaticum Essence – just like Filaticum Model and Gypsum – is member of the product group containing gypsum. Their common characteristic is that the added gypsum changes the usual properties of the plastic, both functionally and aesthetically. The mineral content of Filaticum Essence is minimal, it does not contain pigments, and this combination resulted in an easy-to-use filament. The surface of printed objects is homogeneous, layers are barely visible, and the usual surface roughness is blurred. Mechanical post-processing of objects (polishing, carving, etc.) and painting are easier than in case of standard PLA.
Video about how the Model filament (part of the product group) works in practice:
-
DetailsFilaticum Model
16 990 Ft – 56 590 Ft 13 378 Ft + VAT Add to cartFilaticum Model – just like Filaticum Gypsum and Essence – is member of the product group containing gypsum. Their common characteristic is that the added gypsum changes the usual properties of the plastic, both functionally and aesthetically. The mineral content in the Filaticum Model is medium, less brittle than Gypsum filament, as for its basic characteristics it is between Gypsum and Essence filaments. The printed objects are off-white, with a matte finish, and the details are well outlined, which is useful for modelers. The printed models can be painted much easily than those printed with standard PLA or ABS filaments. The object can be sanded – both dry and wet – , and it is easy to cut, thus most accurate models can be printed with Filaticum Model. It is one of the most versatile Filaticum products.
-
DetailsFilaticum Gypsum
16 990 Ft – 56 590 Ft 13 378 Ft + VAT Add to cartFilaticum Gypsum – just like Filaticum Model and Essence – is member of the product group containing gypsum. Their common characteristic is that the added gypsum changes the usual properties of the plastic, both functionally and aesthetically. Filaticum Gypsum has the highest mineral content, thus it is yellowish, looks like rock or gypsum. The printed objects can be shaped very easily: they can be cut with a sharp tool, sanded, and polished, thus facilitating the post-processing of the object. It is easy to paint also, even with water-based paint. Due to the high mineral content the suggested printing temperature is lower than in case of standard PLA: 185-210 0C. Direct drive is recommended.
Video about how the Model filament (part of the product group) works in practice:
-
DetailsFilaticum Wood
13 490 Ft – 44 890 Ft 10 622 Ft + VAT Add to cartFilaticum Wood filament is designed to create objects resembling real wood in texture and color. Printing settings are the same as those for standard PLA, and you should pay attention to the same things. The nozzle clogging is not an issue with Filaticum Wood, as it I usually a case with wood filaments.
At the same time, the adhesion is excellent, shrinkage is minimal.
The wood effect is also enhanced by the fact that the printed object has a unique touch that is rougher and more natural than PLA. In addition, it is relatively easy to sand and simple to paint.
-
DetailsFilaticum PLA Litho
8 990 Ft – 22 390 Ft 7 079 Ft + VAT Add to cartPLA filament designed for printing lithophanes, for beginners and professionals.
The uniquely developed off-white colour gives a beautifully bright appearance on thin surfaces and a darker, contrasting appearance on thicker surfaces. Printed objects will look like real photographs. Thanks to the additive used to achieve the special optical effect, the printed layers are also less visible, they almost disappear.
-
DetailsFilaticum Fuzzy
9 990 Ft 7 866 Ft + VAT Add to cartFilaticum Fuzzy filament was developed to create unique objects with a special surface. The layers typical for FDM 3D printing are blurred, almost disappeared, as a fluffy, fuzzy surface is formed over them. This is combined with a matt effect.
Filaticum Fuzzy is PLA-based filament, therefore PLA printing settings can be used as a baseline, and then, the surface texture of the printed object can be modified by varying the printing temperature. Recommended bed temperature: 60 °C.
For an even more special look, with a lower flow a surface with “craters” can be achieved.
In addition to the unique surface, the impact resistance of the material is also very good, it is easy to sand, post-process and glue also. The Z-axis adhesion of the print is also better compared to standard PLA filament.
To achieve the characteristic surface, in addition to PLA this filament contains additives, making it somewhat stiffer than usual. Due to the nature of the filament, it is prone to stringing, but this can be easily removed after printing without traces.
The spools weigh 750 grams, but they contain the same amount of filament length as standard 1 kg PLA filaments, so the material requirement should be calculated accordingly.
-
DetailsFilaticum Antiviral
29 990 Ft – 99 890 Ft 23 614 Ft + VAT Add to cartFilaticum Antiviral provides antimicrobial protection for the entire lifetime of 3D printed products. The active substance, built in to the PLA matrix, has been shown to deactivate many kinds of viruses and has been tested to be effective against Feline Coronavirus, H1N1 and Norovirus viruses, among others. The latest tests (according to ISO 21702) by the producer of the active substance confirmed, that the reduction of Covid-19 (SARS-CoV-2) germs is much faster than in the control samples without active substance. Thus, the active substance can be used effectively in the protection against Covid-19, however, the antiviral activity of the 3D printed product has to be tested by the manufacturer of the final product in a specialized laboratory.
-
DetailsFilaticum Antibacterial
27 490 Ft – 91 490 Ft 21 646 Ft + VAT Add to cartFilaticum Antibacterial is a special filament which provides antimicrobial protection against a wide variety of microorganisms. Its antibacterial and fungicide properties are based on metal ions. In objects printed with Filaticum Antibacterial filament, the built-in metal ion complexes block the metabolic processes of bacteria and fungi by an enzymatic reaction, thus preventing their growth. A similar mechanism is present at disinfectants, various preservatives, wash-off and leave-on products.
Filaticum Antibacterial provides lifelong lasting antimicrobial protection against Gram positive (e.g. Enterococcus, Bacillus etc.) and Gram-negative (e.g. Salmonella, Legionella etc.) bacteria, and different fungi, yeasts and algae fungus. Its use is advantageous where the presence of these microorganisms is harmful, e.g. in hospitals, shops, households, beauty salons. With Filaticum Antibacterial, objects exposed to microbial infection can be 3D printed.
The active metal ion substance is incorporated in the PLA polymer matrix, and it does not have any negative impact on PLA’s favorable mechanical and printing properties. Filaticum Antibacterial can be printed in wide range temperature: 195-215 0C, without changing antibacterial properties. Solubility of the active metal ions and their migration to the surface is very low, so the dissolution from 3D printed objects is minimal, providing long-lasting protection for the object.
The active antimicrobial substance has been extensively tested using internationally accepted methods: ISO 22196, ASTM E2180 and JIS standards.
-
DetailsFilaticum Cleaning
1 890 Ft 157 Ft + VAT Add to cartFilaticum Cleaning was designed for cleaning the extruder and the nozzle. This special filament incorporates short glass fibers thus removes staining and polishes the inner surface. Recommendation of use: print about 20 cm filament which cleans the extruder. If the outflow material clean, it means that the extruder is also clean. In some cases a little bit more material is needed. The efficiency of the cleaning process could increase, if you stop the printing for a while and then continue it. Regular use of Filaticum Cleaning reduces the plugging, increase the shelf life of the extruder. It is also strongly recommended if you changes often the different colored filaments or swap different raw materials.
-
Details
Filaticum Support
11 690 Ft – 38 890 Ft 8 661 Ft + VAT Add to cartFilaticum Support is a PLA-based filament, developed for 3D printings which need support.
As opposed to the soluble support materials Filaticum Support is an easy to break-away filament, so the vast majority of the support material can be removed quickly. Any remaining support on the surface can be completely removed by sanding. The result is a clean printing surface, there is no or minimal need for post-processing.
Also suitable for printing the complexly structured supports. It is compatible with FDM filaments and works well with them.
Printing with Filaticum Support is simple, settings are similar to PLA’s: printing temperature 190-215 0C, bed temperature 60 0C.
-
DetailsFilaticum Glass Reinforced
18 990 Ft – 63 290 Ft 14 953 Ft + VAT Add to cartThe strength, hardness, and heat resistance of filament reinforced with glass fiber go far beyond the characteristics of the standard PLA. It can withstand heat of up to 100 0C. The biopolymer-based filament is also suitable for printing lightweight parts, even applicable for replacing metal parts. The printed surface is unique, glassy, so it is also a perfect choice for designers. The warping of objects printed with Filaticum Glass Reinforced is very low. Recommended printing parameters: 215 0C nozzle, 60 0C bed. If you are printing continuously in bigger quantities (above 1-2 kg), hard nozzles are recommended, in this case the printing parameters should be adjusted accordingly. Direct drive is recommended.
-
DetailsFilaticum High Transparent
14 990 Ft – 49 890 Ft 11 803 Ft + VAT Add to cartTransparent PLA filaments have a slight yellowish color, in addition, if you print thicker objects, the transparency disappears. With Filaticum High Transparent you can get an almost water-clear finish. It is an easy-to-print filament, in a wide range of printing temperature. The transparency of the printed object can be improved by changing the printing parameters: a nozzle with larger diameter, and the lowest possible layer height. It’s important to know that the texture of the print can also affect the transparency, and the best results can be obtained by printing single-layer walls.